Browsing by Author "Beeby, Steve"

Now showing 1 - 3 of 3
  • Thumbnail Image
    ItemOpen Access
    CNTs-added PMNT/PDMS flexible piezoelectric nanocomposite for energy harvesting application
    (Taylor and Francis, 2018-04-05) Promsawat, Napatporn; Promsawat, Methee; Janphuang, Phatthanapong; Beeby, Steve; Rojviriya, Catleya; Pakawanit, Phakkhananan; Pojprapai, Soodkhet; Luo, Zhenhua
    The flexible piezoelectric nanocomposites based on lead magnesium niobate titanate [Pb(Mg1/3Nb2/3)0.65Ti0.35O3; PMNT] particles in polydimethylsiloxane (PDMS) matrix were fabricated and characterized. PMNT powders are synthesized using the columbite precursor method. PMNT/PDMS flexible nanocomposites are then prepared by spin casting technique, where a small amount of carbon nanotubes (CNTs) is added into the PMNT/PDMS composite to enhance cross-links between PMNT particles and PDMS matrix. The phase and microstructure of the nanocomposite are investigated by using X-ray diffraction and scanning electron microscope (SEM). The electromechanical behavior is evaluated by using an autonomous pneumatic actuator. The flexible composite, occupying approximately 300 mm2, is capable of generating an open-circuit voltage (Voc) of 2.83 ± 0.24 V and a short-circuit current (Isc) signal of 0.33 ± 0.01 µA across 10 Ω resistor under mechanical load of 300 N. The generated electrical charges are 29026 pC. The relative dielectric constant is measured at 10 kHz and found to be 6.76 ± 1.15. The piezoelectric PMNT/PDMS composite can potentially be used in a variety of applications such as wearable sensors, actuators, and energy harvesting for converting kinetic energy into useful electrical energy.
  • Thumbnail Image
    ItemOpen Access
    E-textile technology review - from materials to application
    (IEEE, 2021-07-02) Komolafe, Abiodun; Zaghari, Bahareh; Torah, Russel; Weddell, Alex S.; Khanbareh, Hamideh; Tsikriteas, Zois Michail; Vousden, Mark; Wagih, Mahmoud; Jurado, Ulises Tronco; Shi, Junjie; Yong, Sheng; Arumugam, Sasikumar; Li, Yi; Yang, Kai; Savelli, Guillaume; White, Neil M.; Beeby, Steve
    Wearable devices are ideal for personalized electronic applications in several domains such as healthcare, entertainment, sports and military. Although wearable technology is a growing market, current wearable devices are predominantly battery powered accessory devices, whose form factors also preclude them from utilizing the large area of the human body for spatiotemporal sensing or energy harvesting from body movements. E-textiles provide an opportunity to expand on current wearables to enable such applications via the larger surface area offered by garments, but consumer devices have been few and far between because of the inherent challenges in replicating traditional manufacturing technologies (that have enabled these wearable accessories) on textiles. Also, the powering of e-textile devices with battery energy like in wearable accessories, has proven incompatible with textile requirements for flexibility and washing. Although current e-textile research has shown advances in materials, new processing techniques, and one-off e-textile prototype devices, the pathway to industry scale commercialization is still uncertain. This paper reports the progress on the current technologies enabling the fabrication of e-textile devices and their power supplies including textile-based energy harvesters, energy storage mechanisms, and wireless power transfer solutions. It identifies factors that limit the adoption of current reported fabrication processes and devices in the industry for mass-market commercialization.
  • Thumbnail Image
    ItemOpen Access
    Flexible piezoelectric nano-composite films for kinetic energy harvesting from textiles
    (Elsevier, 2017-01-17) Almusallam, Ahmed; Luo, Zhen-Hua; Komolafe, Abiodun; Yang, Kai; Robinson, Andrew; Torah, Russel; Beeby, Steve
    This paper details the enhancements in the dielectric and piezoelectric properties of a low-temperature screen-printable piezoelectric nano-composite film on flexible plastic and textile substrates. These enhancements involved adding silver nano particles to the nano-composite material and using an additional cold isostatic pressing (CIP) post-processing procedure. These developments have resulted in a 18% increase in the free-standing piezoelectric charge coefficient d33 to a value of 98 pC/N. The increase in the dielectric constant of the piezoelectric film has, however, resulted in a decrease in the peak output voltage of the composite film. The potential for this material to be used to harvest mechanical energy from a variety of textiles under compressive and bending forces has been evaluated theoretically and experimentally. The maximum energy density of the enhanced piezoelectric material under 800 N compressive force was found to be 34 J/m3 on a Kermel textile. The maximum energy density of the enhanced piezoelectric material under bending was found to be 14.3 J/m3 on a cotton textile. These results agree very favourably with the theoretical predictions. For a 10x10 cm piezoelectric element 100 µm thick this equates to 38 μJ and 14.3 μJ of energy generated per mechanical action respectively which is a potentially useful amount of energy.