Browsing by Author "De Marchi, Andrea"

Now showing 1 - 3 of 3
  • Thumbnail Image
    ItemOpen Access
    Measurement of weak non-linear response of Kevlar® fibre damaged by UV exposure
    (Elsevier, 2017-10-21) Ceravolo, Rosario; De Marchi, Andrea; Pinotti, Elena; Surace, Cecilia; Zanotti Fragonara, Luca
    This paper deals with a high-sensitivity method for the assessment of damage in high-strength fibres exposed to UV radiation. A recently developed experimental testing machine, based on an optical measurement system and electro-magnetic driving force, was used to characterize fibre materials. Stiffness, damping, and non-linearity were measured on several Kevlar® fibre samples previously exposed to UV light for different lengths of time. The results show that UV radiation increases the material non-linearity by amounts which can be clearly observed even at low vibration amplitudes. On the contrary, uncertainties affecting the determination of stiffness and damping with the adopted approach don’t seem to allow a similarly unambiguous UV damage assessment. Result confirm our initial hypothesis that non-linearity may be a valuable index of damage, at least in case of UV exposure, for applications in the Structural Health Monitoring (SHM) field.
  • Thumbnail Image
    ItemOpen Access
    A new testing machine for the dynamic characterization of high strength low damping fiber materials
    (Springer, 2016-09-14) Ceravolo, Rosario; De Marchi, Andrea; Pinotti, Elena; Surace, Cecilia; Zanotti Fragonara, Luca
    This work describes a novel method for measuring the damping, the elastic modulus and the non-linear behavior of high strength low damping fiber materials such as para-aramids, silicon carbide (SiC) and carbon. The method is based on resonant response characterization of a spring-mass system excited by a sine-wave forcing term which is applied as a vertical force to the suspended mass. The damping is obtained from the measured resonance quality factor Q, the elasticity modulus is calculated from the resonance frequency, and the non-linear coefficient is obtained with the backbone approach from resonance profile variations as a function of the forcing term amplitude. It is argued that the method is very sensitive, to the point that a maximum excitation amplitude of the order of a few percent of resistance is sufficient to obtain an estimate of the non-linear coefficient. This claim is supported by experimental results. A testing machine is also discussed, which provides the necessary sensitivity at such small excitation amplitudes and the capability of evaluating very small damping values, as expected in high strength low damping fiber materials. The sensitivity is guaranteed by an optical position sensor with sub-micron resolution. To evaluate small damping values, particular care has been taken to ensure that energy dispersions in the generator are much smaller than energy dispersions in the fibers themselves. Examples of dynamic characterization are shown for para-aramid, silicon carbide, and carbon fibers.
  • Thumbnail Image
    ItemOpen Access
    Non-destructive testing on aramid fibres for the long-term assessment of interventions on heritage structures
    (IOP Publishing: Conference Series / Institute of Physics (IoP), 2015-07-09) Ceravolo, Rosario; De Marchi, Andrea; Pinotti, Elena; Surace, Cecilia; Zanotti Fragonara, Luca
    High strength fibre reinforced polymers (FRPs) are composite materials made of fibres such as carbon, aramid and/or glass, and a resin matrix. FRPs are commonly used for structural repair and strengthening interventions and exhibit high potential for applications to existing constructions, including heritage buildings. In regard to aramid fibres, uncertainties about the long-term behaviour of these materials have often made the designers reluctant to use them in structural engineering. The present study describes simple and non-destructive nonlinearity tests for assessing damage or degradation of structural properties in Kevlar fibres. This was obtained by using high precision measurements to detect small deviations in the dynamic response measured on fibres and ropes. The change in dynamic properties was then related to a damage produced by exposure of the sample to UV rays for a defined time period, which simulated long-term sun exposure. In order to investigate the sensitivity of such an approach to damage detection, non-linearity characterisation tests were conducted on aramid fibres in both damaged and undamaged states. With the purpose of carrying out dynamic tests on small fibre specimens, a dedicated instrumentation was designed and built in cooperation with the Metrology Laboratory of the Department of Electronics at the Politecnico di Torino.