Browsing by Author "Chen, Si"
Now showing 1 - 9 of 9
Results Per Page
Sort Options
Item Open Access Aerodynamic analysis of a flapping wing aircraft for short landing(MDPI, 2020-05-14) Ji, Bing; Zhu, Zenggang; Guo, Shijun; Chen, Si; Zhu, Qiaolin; Li, Yushuai; Yang, Fan; Song, Rui; Li, YibinAn investigation into the aerodynamic characteristics has been presented for a bio-inspired flapping wing aircraft. Firstly, a mechanism has been developed to transform the usual rotation powered by a motor to a combined flapping and pitching motion of the flapping wing. Secondly, an experimental model of the flapping wing aircraft has been built and tested to measure the motion and aerodynamic forces produced by the flapping wing. Thirdly, aerodynamic analysis is carried out based on the measured motion of the flapping wing model using an unsteady aerodynamic model (UAM) and validated by a computational fluid dynamics (CFD) method. The difference of the average lift force between the UAM and CFD method is 1.3%, and the difference between the UAM and experimental results is 18%. In addition, a parametric study is carried out by employing the UAM method to analyze the effect of variations of the pitching angle on the aerodynamic lift and drag forces. According to the study, the pitching amplitude for maximum lift is in the range of 60°~70° as the flight velocity decreases from 5 m/s to 1 m/s during landing.Item Open Access Aerodynamic analysis of insect-like flapping wings in fan-sweep and parallel motions with the slit effect(Elsevier, 2022-05-23) Zhu, Zenggang; Zhao, Jingtai; He, Yuanyuan; Guo, Shijun; Chen, Si; Ji, BingIn this study, the aerodynamic performance of flapping wings using a parallel motion was investigated and compared with the insect-like “fan-sweep” motion, and the effect of adding a slit to the wings was analyzed. First, numerical simulations were performed to analyze the wing aerodynamics of two flapping motions with equivalent stroke amplitudes over a range of pitching angles based on computational fluid dynamics (CFD). The simulation results indicated that flapping wings with a rapid and short parallel motion achieved better lift and efficiency than those of the fan-sweep motion while maintaining the same aerodynamic characteristics regarding stall delay and leading-edge vortices. For a parallel motion with a pitching angle of 25° and 100 mm stroke amplitude, the wings generated an average lift of 8.4 gf with a lift-to-drag ratio of 1.06, respectively, which were 1.8% and 26% greater than those of the fan-sweep motion with a corresponding 96° stroke amplitude. This situation was reversed when the pitching angle and stroke amplitude were increased to 45° and 144° for the fan-sweep motion, which was equivalent to the parallel motion with a 150 mm stroke amplitude. The slit effect in the parallel motion was also evaluated, and the CFD results indicated that a slit width of 1 mm (1/50 wing chord) increased the lift of the wing by approximately 27% in the case of the 150 mm stroke amplitude. Further, the slit width slightly influenced the lift and aerodynamic efficiency.Item Open Access Aerodynamic performance of a flyable flapping wing rotor with passive pitching angle variation(IEEE, 2021-09-22) Chen, Si; Wang, Le; He, Yuanyuan; Tong, Mingbo; Pan, Yingjun; Ji, Bing; Guo, ShijunThe present work was based on an experimental study on the aerodynamic performance of a flapping wing rotor (FWR) and enhancement by passive pitching angle variation (PPAV) associated with powered flapping motion. The PPAV (in this study 10o~50o) was realized by a specially designed sleeve-pin unit as part of a U-shape flapping mechanism. Through experiment and analysis, it was found that the average lift produced by an FWR of PPAV was >100% higher than the baseline model, the same FWR of a constant pitching angle 30o under the same input power. It was also noted that the lift-voltage relationship for the FWR of PPAV was almost linear and the aerodynamic efficiency was also over 100% higher than the baseline FWR when the input voltage was under 6V. The aerodynamic lift or efficiency of the FWR of PPAV can be also increased significantly by reducing the weight of the wings. An FWR model was fabricated and achieved vertical take-off and free flight powered by 9V input voltage. The mechanism of PPAV function provides a feasible solution for aerodynamic improvement of a bio-inspired FWR and potential application to micro-air-vehicles (MAVs).Item Open Access Analysis and testing of a flyable micro flapping-wing rotor with a highly efficient elastic mechanism(MDPI, 2024-12-03) Pan, Yingjun; Su, Huijuan; Guo, Shijun; Chen, Si; Huang, XunA Flapping-Wing Rotor (FWR) is a novel bio-inspired micro aerial vehicle configuration, featuring unique wing motions which combine active flapping and passive rotation for high lift production. Power efficiency in flight has recently emerged as a critical factor in FWR development. The current study investigates an elastic flapping mechanism to improve FWRs’ power efficiency by incorporating springs into the system. The elastic force counteracts the system inertia to accelerate or decelerate the wing motion, reducing the power demand and increasing efficiency. A dynamic model was developed to simulate the unique kinematics of the FWR’s wing motions and its elastic mechanism, considering the coupling of aerodynamic and inertial forces generated by the wings, along with the elastic and driven forces from the mechanism. The effects of the spring stiffness on the aerodynamic performance and power efficiency were investigated. The model was then verified through experimental testing. When a spring stiffness close to the mechanical system resonance was applied, the power efficiency of the test model increased by 16% compared to the baseline model without springs, generating an equivalent average lift. With an optimal elastic flapping mechanism for greater lift and lower power consumption, the FWR was fully constructed with onboard power and a control receiver weighing 27.79 g, successfully achieving vertical take-off flight. The current model produces ten times greater lift and has nearly double the wing area of the first 2.6 g flyable FWR prototype.Item Open Access A bio-inspired flapping wing rotor of variant frequency driven by ultrasonic motor(MDPI, 2020-01-06) Chen, Si; Wang, Le; Guo, Shijun; Zhao, Chunsheng; Tong, MingboBy combining the flapping and rotary motion, a bio-inspired flapping wing rotor (FWR) is a unique kinematics of motion. It can produce a significantly greater aerodynamic lift and efficiency than mimicking the insect wings in a vertical take-off and landing (VTOL). To produce the same lift, the FWR’s flapping frequency, twist angle, and self-propelling rotational speed is significantly smaller than the insect-like flapping wings and rotors. Like its opponents, however, the effect of variant flapping frequency (VFF) of a FWR, during a flapping cycle on its aerodynamic characteristics and efficiency, remains to be evaluated. A FWR model is built to carry out experimental work. To be able to vary the flapping frequency rapidly during a stroke, an ultrasonic motor (USM) is used to drive the FWR. Experiment and numerical simulation using computational fluid dynamics (CFD) are performed in a VFF range versus the usual constant flapping frequency (CFF) cases. The measured lifting forces agree very well with the CFD results. Flapping frequency in an up-stroke is smaller than a down-stroke, and the negative lift and inertia forces can be reduced significantly. The average lift of the FWR where the motion in VFF is greater than the CFF, in the same input motor power or equivalent flapping frequency. In other words, the required power for a VFF case to produce a specified lift is less than a CFF case. For this FWR model, the optimal installation angle of the wings for high lift and efficiency is found to be 30° and the Strouhal number of the VFF cases is between 0.3–0.36. View Full-TextItem Open Access Design and experiment of a bionic flapping wing mechanism with flapping–twist–swing motion based on a single rotation(AIP Publishing, 2020-06-12) Ji, Bing; Zhu, Qiaolin; Guo, Shijun; Yang, Fan; Li, Yushuai; Zhu, Zenggang; Chen, Si; Song, Rui; Li, YibinIn the present study, a bionic flapping mechanism of a spatial six-bar configuration was designed to transform a single rotation of a motor into a three degrees of freedom “flapping–twist–swing” cooperative motion of a flapping wing. The kinematics model of the flapping mechanism movement was constructed. The flapping trajectory of the wing based on the kinematics model was to mimic the motion of a pigeon wing in landing flight. To reduce the manufacturing complexity, the flapping mechanism was simplified with only two degrees of freedom (flapping and twist) retained. Finally, a prototype model with a 0.9 m wing span was built and tested. A comparison among the experimental data, theoretical calculation results, and ADAMS simulation results revealed that the difference in the flapping and the twist amplitude between experimental observations and theoretical calculation results was 12.5% and 2.3%, respectively. This was owing to the elastic deformation of the bar and the mechanism simplification. The comparison results also indicated that the maximum difference in the inertial force was 5.9% in up-stroke and 6.7% in down-stroke, respectively. The experimental results showed that the inertial force of the model with the wing patagium was approximately 2.2 N, and the maximum positive and negative lift was 2.1 N and −1.5 N, respectively. It is hoped that this study can provide guidance for the design of bionic flapping wing mechanisms of a flapping wing aircraft for short landing flight.Item Open Access Effect of asymmetric feathering angle on the aerodynamic performance of a flyable bionic flapping-wing rotor(MDPI, 2023-03-18) Chen, Si; Wang, Le; Guo, Shijun; Tong, Mingbo; He, YuanyuanThe current study involves an experimental as well as numerical study on the aerodynamic behavior of a flapping-wing rotor (FWR) with different feathering amplitudes (−20°–50°, −50°–20°, and −35°–35°). In order to fulfil the experimental test, an FWR which weighs 18.7 g is designed in this manuscript. According to the experimental and numerical results, it was observed that, compared with the cases under a zero average stroke angle, the cases under a positive average stroke angle or negative average stroke angle share a higher rotary speed given the same input voltage. Despite the fact that the negative average stroke angle would facilitate the generation of a higher rotary speed, the negative average stroke angle cases tend to generate the smallest lift-to-power ratio. On the other hand, the cases with a positive average stroke angle tend to share the largest lift-to-power ratio (about 1.25 times those of zero average stroke angle cases and about 1.6 times those of negative average stroke angle cases). The above study indicates that the application of a positive average stroke angle can provide an effective solution to further increase the aerodynamic performance of a bio-inspired FWR.Item Open Access Short landing performance and scale effect of a flapping wing aircraft(ASCE, 2020-09-15) Chen, Si; Guo, Shijun; Li, Hao; Tong, Mingbo; Ji, BingAn investigation was made into the performance and scale effect of birdlike flapping wing aircraft in short landing. A flapping mechanism is proposed to transform a powered shaft rotation to an optimal kinematics of wing motion combining up-and-down stroke, pitching, and fore-and-back swing. An unsteady aerodynamic method (UAM) was developed based on potential flow theory, including the leading- and trailing-edge vortices generated by a flapping wing. After validation based on computational fluid dynamics (CFD) results, the method is used to calculate the aerodynamic forces of flapping wings. The flight dynamics model of the aircraft is built using Automated Dynamic Analysis of Mechanical Systems (ADAMS) software version 2012 interfacing with the UAM coded in Python. The coupling between the inertial force of the body motion and the aerodynamic forces from flapping wings and tailplane is incorporated into the numerical simulation of the aircraft landing. Taking a 0.196-kg birdlike aircraft model with a prescribed kinematics of flapping wing motion as an example, a parametric study was carried out in a small range of initial tailplane angles and subsequent flapping frequencies. Optimal parameters were obtained to reduce the forward and descending velocities of the aircraft to a minimum value for safe and short landing performance. The study is then extended to aircraft of different geometric scales in a range of 0.5–10 associated with a weight scale of 0.1–1,000. Based on the study, a method is developed to determine the required flapping frequency for birdlike aircraft of different scales to achieve a short landing target with the descending velocity reduced to a specified value. For the aforementioned example aircraft (geometric scale of 1), the flapping frequency is 4 Hz to reduce both descending and forward velocities to 50% of the landing performance in fixed-wing mode, while a birdlike aircraft on a geometric scale of 10 and landing weight of 196 kg requires a minimum flapping frequency of 1.25 Hz to achieve a 50% reduction of the descending and forward velocities compared with the same aircraft landing in fixed-wing mode.Item Open Access Unsteady aerodynamic model of flexible flapping wing(Elsevier, 2018-08-17) Chen, Si; Li, Hao; Guo, Shijun; Tong, Mingbo; Ji, BingBio-inspired flapping wing has potential application to micro air vehicles (MAV). Due to the nature of lightweight and flexibility of micro flapping wing structures, elastic deformation as a result of aeroelastic coupling is inevitable in flapping motion. This effect can be significant and beneficial to the aerodynamic performance as revealed in the present investigation for a flexible flapping wing of variable camber versus a rigid one. Firstly a two dimensional (2D) unsteady aerodynamic model (UAM) based on potential flow theory has been extended from previous study. Both leading and trailing edge discrete vortices are included in the model with unsteady Kutta condition satisfied to fully characterize the unsteady flow around a flapping wing. A wall function is created to modify the induced velocity of the vortices in the UAM to solve the vortices penetration problem. The modified UAM is then validated by comparing with CFD results of a typical insect-like flapping motion from previous research. Secondly the UAM is further extended for a flexible flapping wing of camber variation. Comparing with a rigid wing in a prescribed plunging and pitching motion, the results show lift increase with positive camber in upstroke by mitigating negative lift. The results also agree well with CFD simulation. Thirdly the 2D UAM is extended to calculate the aerodynamic forces of a 3D wing with camber variation, and validated by CFD results. Finally the model is applied to aerodynamic analysis of a 3D flexible flapping wing with aeroelastic coupling effect. Significant increase of lift coefficient can be achieved for a flexible flapping wing of positive camber and twist in upstroke produced by the structure elastic deformation.