CERES :: Browsing by Author "Rahatekar, Sameer S."

Browsing by Author "Rahatekar, Sameer S."

Now showing 1 - 20 of 21

Open Access
Alginate films augmented with chlorhexidine hexametaphosphate particles provide sustained antimicrobial properties for application in wound care
(Springer, 2020-03-11) Duckworth, Peter F.; Maddocks, Sarah E.; Rahatekar, Sameer S.; Barbour, Michele E.
All chronic wounds are colonised by bacteria; for some, colonisation progresses to become infection. Alginate wound dressings are used for highly exuding chronic wounds as they are very absorbent, taking up large quantities of exudate while maintaining a moist wound bed to support healing. Some alginate dressings are doped with antimicrobials, most commonly silver, but evidence regarding the efficacy of these is largely inconclusive. This manuscript describes the development and in vitro assessment of alginate materials doped with chlorhexidine hexametaphosphate (CHX-HMP), a sparingly soluble salt which when exposed to aqueous environments provides sustained release of the common antiseptic chlorhexidine. Comparator materials were a commercial silver alginate dressing material and an alginate doped with chlorhexidine digluconate (CHXdg). CHX-HMP alginates provided a dose-dependent CHX release which was sustained for over 14 days, whereas CHXdg alginates released limited CHX and this ceased within 24 h. CHX-HMP and silver alginates were efficacious against 5 major wound pathogens (MRSA, E. coli, P. aeruginosa, K. pneumoniae, A. baumannii) in a total viable count (TVC) and an agar diffusion zone of inhibition (ZOI) model. At baseline the silver alginate was more effective than the CHX-HMP alginate in the TVC assay but the CHX-HMP alginate was the more effective in the ZOI assay. After 7 days’ artificial aging the CHX-HMP alginate was more effective than the silver alginate for four of the five bacteria tested in both assays. These materials may ultimately find application in the development of wound dressings for chronic wounds that provide sustained antimicrobial protection
Open Access
Carbon nanotube films spun from a gas phase reactor for manufacturing carbon nanotube film/carbon fibre epoxy hybrid composites for electrical applications
(Elsevier, 2019-09-06) Chen, Jinhu; Lekawa-Raus, Agnieszka; Trevarthen, James; Gizewski, Tomasz; Lukawski, Damian; Hazra, Kalyan; Rahatekar, Sameer S.; Koziol, Krzysztof K. K.
Working towards improvement of the electrical performance of carbon fibre (CF) reinforced polymer composites used in aircrafts, we have developed new routes of production of hybrid carbon nanotube (CNT)/CF epoxy composites. It was shown that the use of CNT films produced via one-step chemical vapour deposition (CVD) based method and in-process control of films morphology combined with standard vacuum bagging based manufacture of the composites results in very good electrical performance of the final material, delivering high potential for lightning strike related applications including electromagnetic interference (EMI) shielding and static dissipation for the composite components used in aerospace and transport sector. Simultaneously, the process is much simpler, inexpensive and easy to upscale than previously proposed methods.
Open Access
Deformation mechanisms in ionic liquid spun cellulose fibers
(Elsevier, 2016-07-05) Wanasekara, Nandula D.; Michud, Anne; Zhu, Chenchen; Rahatekar, Sameer S.; Sixta, Herbert; Eichhorn, Stephen J.
The molecular deformation and crystal orientation of a range of next generation regenerated cellulose fibers, produced from an ionic liquid solvent spinning system, are correlated with macroscopic fiber properties. Fibers are drawn at the spinning stage to increase both molecular and crystal orientation in order to achieve a high tensile strength and Young’s modulus for potential use in engineering applications. Raman spectroscopy was utilized to quantify both molecular strain and orientation of fibers deformed in tension. X-ray diffraction was used to characterize crystal orientation of single fibers. These techniques are shown to provide complimentary information on the microstructure of the fibers. A shift in the position of a characteristic Raman band, initially located at ∼1095 cm−1, emanating from the backbone structure of the cellulose polymer chains was followed under tensile deformation. It is shown that the shift rate of this band with respect to strain increases with the draw ratio of the fibers, indicative of an increase in the axial molecular alignment and subsequent deformation of the cellulose chains. A linear relationship between the Raman band shift rate and the modulus was established, indicating that the fibers possess a series aggregate structure of aligned crystalline and amorphous domains. Wide-angle X-ray diffraction data show that crystal orientation increases with an increase in the draw ratio, and a crystalline chain slip model was used to fit the change in orientation with fiber draw ratio. In addition to this a new model is proposed for a series aggregate structure that takes into better account the molecular deformation of the fibers. Using this model a prediction for the crystal modulus of a cellulose-II structure is made (83 GPa) which is shown to be in good agreement with other experimental approaches for its determination.
Open Access
Development of hybrid electrospun alginate-pulverized moringa composites
(Royal Society of Chemistry, 2024-03-12) Orisawayi, Abimbola Oluwatayo; Koziol, Krzysztof K. K.; Hao, Shuai; Tiwari, Shivam; Rahatekar, Sameer S.
The consideration of biopolymers with natural products offers promising and effective materials with intrinsic and extrinsic properties that are utilized in several applications. Electrospinning is a method known for its unique and efficient performance in developing polymer-based nanofibers with tunable and diverse properties presented as good surface area, morphology, porosity, and fiber diameters during fabrication. In this work, we have developed an electrospun sodium alginate (SA) incorporated with pulverized Moringa oleifera seed powder (PMO) as a potential natural biosorbent material for water treatment applications. The developed fibers when observed using a scanning electron microscope (SEM), presented pure sodium alginate with smooth fiber (SAF) characteristics of an average diameter of about 515.09 nm (±114.33). Addition of pulverized Moringa oleifera at 0.5%, 2%, 4%, 6%, and 8% (w/w) reduces the fiber diameter to an average of about 240 nm with a few spindle-like pulverized Moringa oleifera particles beads of 300 nm (±77.97) 0.5% particle size and 110 nm (±32.19) with the clear observation of rougher spindle-like pulverized Moringa oleifera particle beads of 680 nm (±131.77) at 8% of alginate/Moringa oleifera fiber (AMF). The results from the rheology presented characteristic shear-thinning or pseudoplastic behaviour with a decline in viscosity, with characteristic behaviour as the shear rate increases, indicative of an ideal polymer solution suitable for the spinning process. Fourier transform infrared spectroscopy (FT-IR) shows the presence of amine and amide functional groups are prevalent on the alginate-impregnated moringa with water stability nanofibers and thermogravimetric analysis (TGA) with change in degradation properties in a clear indication and successful incorporation of the Moringa oleifera in the electrospun fiber. The key findings from this study position nanofibers as sustainable composites fiber for potential applications in water treatment, especifically heavy metal adsorption.
Open Access
Electrospinning alginate/polyethylene oxide and curcumin composite nanofibers
(Elsevier, 2020-03-16) Javier, Gutierrez Gonzalez; Esther, Garcia-Cela; Magan, Naresh; Rahatekar, Sameer S.
Manufacturing a sodium alginate (SA) and polyethylene oxide (PEO) composite loaded with curcumin (CU) was accomplished in this study by using electrospinning. These composite nanofibers were crosslinked using trifluoroacetic acid (TFA) mechanically characterized along with the morphological properties of the composite nanofiber mesh. We were successful in manufacturing the composite nanofibers with a wide range of CU concentrations ranging from 10 to 40 wt%. Firstly, dissolved in a saturated water/CU solution it was added to SA/PEO blending, homogenized and electrospun. Mechanical properties were affected by both CU addition and the cross-linking process, resulting in a higher ultimate tensile stress (MPa) (from 4.3±2 to 15.1±2 at 10% CU) and Young modulus (GPa) (0.0076±0.003, 0.044±0.003 before and after TFA). CU was successfully encapsulated in the SA nanofibers and excellent mechanical properties were obtained. By using a biocompatible TFA crosslinking and the natural properties of alginate this nanofiber composite could potentially be used for filtering, environmental pollution control, food packaging and for tissue engineering.
Open Access
Enhanced oral bioavailability and hepatoprotective activity of thymoquinone in the form of phospholipidic nano-constructs
(Taylor and Francis, 2020-01-31) Rathore, C.; Upadhyay, N.; Kaundal, R.; Dwivedi, R. P.; Rahatekar, Sameer S.; John, A.; Dua, K; Tambuwala, M. M.; Jain, S.; Chaudari, D.; Negi, P.
Background: The poor biopharmaceutical properties of thymoquinone (TQ) obstruct its development as a hepatoprotective agent. To surmount the delivery challenges of TQ, phospholipid nanoconstructs (PNCs) were constructed. Method: PNCs were constructed employing microemulsification technique and systematic optimization by three-factor three level Box-Behnken design. Result: Optimized PNC composition exhibited nano size (<100 nm), spherical morphology, within acceptable range of polydispersity index (0.55), high drug entrapment efficiency (>90%), controlled drug release pattern, and neutral surface charge (zeta potential of −0.65 mV). After oral administration of a single dose of PNC, it showed a relative bioavailability of 386.03% vis-à-vis plain TQ suspension. Further, TQ-loaded PNC demonstrated significant enhanced hepato-protective effect vis-à-vis pure TQ suspension and silymarin, as evidenced by reduction in the ALP, ALT, AST, bilirubin, and albumin level and ratified by histopathological analysis. Conclusion: TQ-loaded PNCs can be efficient nano-platforms for the management of hepatic disorders and promising drug delivery systems to enhance oral bioavailability of this hydrophobic molecule.
Open Access
Environmentally benign alginate extraction and fibres spinning from different European Brown algae species
(Elsevier, 2022-12-08) Silva, Mariana P.; Badruddin, Ishrat Jahan; Tonon, Thierry; Rahatekar, Sameer S.; Gomez, Leonardo D.
Applications of natural fibres are expanding, and sustainable alternatives are needed to support this growing demand. We investigated the production of fibres using alginates from Saccharina latissima (SAC), Laminaria digitata (LAM), Sacchoriza polyschides (SACC), and Himanthalia spp. (HIM). After extraction (3 % w/v biomass) using a sustainable protocol based on citric acid, crude alginate represented 61–65 % of the biomass dry weight for SAC and LAM, and 34–41 % for SACC and HIM when experiments were performed at small scale (1.5 g of starting material). Interestingly, scaling-up extraction (60 g of starting material) decreased yields to 26–30 %. SAC and LAM alginates had the highest M/G (mannuronic acid/guluronic acid) ratios and molecular weights when compared to those from SACC and HIM (M/G:1.98 and 2.23, MW: 302 and 362 kDa, vs 1.83 and 1.86, 268 and 168 kDa). When the four types of alginates were tested for spinning fibres cross-linked with CaCl2, only SAC and LAM alginates produced fibres. These fibres showed no clumps or cracks under stretching action and presented a similar Young's modulus (2.4 and 2.0 GPa). We have demonstrated that alginate extracted from S. latissima and L. digitata can be successfully spun into functional fibres cross-linked with CaCl2.
Open Access
Extrusion dwell time and its effect on the mechanical and thermal properties of pitch/LLDPE blend fibres
(MDPI, 2021-12-05) Aldosari, Salem Mohammed; Rahatekar, Sameer S.
Mesophase pitch-based carbon fibres have excellent resistance to plastic deformation (up to 840 GPa); however, they have very low strain to failure (0.3) and are considered brittle. Hence, the development of pitch fibre precursors able to be plastically deformed without fracture is important. We have previously, successfully developed pitch-based precursor fibres with high ductility (low brittleness) by blending pitch and linear low-density polyethylene. Here, we extend our research to study how the extrusion dwell time (0, 6, 8, and 10 min) affects the physical properties (microstructure) of blend fibres. Scanning electron microscopy of the microstructure showed that by increasing the extrusion dwell from 0 to 10 min the pitch and polyethylene components were more uniformly dispersed. The tensile strength, modulus of elasticity, and strain at failure for the extruded fibres for different dwell times were measured. Increased dwell time resulted in an increase in strain to failure but reduced the ultimate tensile strength. Thermogravimetric analysis was used to investigate if increased dwell time improved the thermal stability of the samples. This study presents a useful guide to help with the selection of mixes of linear low-density polyethylene/pitch blend, with an appropriate extrusion dwell time to help develop a new generation of potential precursors for pitch-based carbon fibres.
Open Access
Fabrication and characterisation of short fibre reinforced elastomer composites for bending and twisting magnetic actuation
(Elsevier, 2016-10-04) Stanier, David C.; Ciambella, Jacopo; Rahatekar, Sameer S.
Polydimethylsiloxane (PDMS) films reinforced with short Nickel-coated Carbon Fibres (NiCF) were successfully fabricated, with the fibres aligned along different directions using an external magnetic field. The fibres were dispersed in the host matrix using sonication and mechanical mixing before being cured for 48 h in the magnetic field; thanks to the nickel functionalisation, the fibre orientation was achieved by a low intensity field (<0.2 T) which required an inexpensive experimental set-up. The main focus of this study was looking at the actuation potential of this magnetic composite material; successful actuation was achieved, showing its large displacement capability. The results confirm the presence of an instability controlled by the magnetic torque, as predicted by the introduced model. The composite films undergo a transition from a bending-only deformed configuration for the 0° fibre specimen, to a twisting-only configuration, achieved for fibres at 90°, whereas all the intermediate angles show both bending and twisting. This behaviour mirrors that which is used to propel a selection of marine mammals.
Open Access
High modulus regenerated cellulose fibers spun from a low molecular weight microcrystalline cellulose solution
(American Chemical Society, 2016-07-27) Zhu, Chenchen; Richardson, Robert M.; Potter, Kevin D.; Koutsomitopoulou, Anastasia F.; van Duijneveldt, Jeroen S.; Vincent, Sheril R.; Wanasekara, Nandula D.; Eichhorn, Stephen J.; Rahatekar, Sameer S.
We have developed a novel process to convert low molecular weight microcrystalline cellulose into stiff regenerated cellulose fibers using a dry-jet wet fiber spinning process. Highly aligned cellulose fibers were spun from optically anisotropic microcrystalline cellulose/1-ethyl-3-methylimidazolium diethyl phosphate (EMImDEP) solutions. As the cellulose concentration increased from 7.6 to 12.4 wt %, the solution texture changed from completely isotropic to weakly nematic. Higher concentration solutions (>15 wt %) showed strongly optically anisotropic patterns, with clearing temperatures ranging from 80 to 90 °C. Cellulose fibers were spun from 12.4, 15.2, and 18.0 wt % cellulose solutions. The physical properties of these fibers were studied by scanning electron microscopy (SEM), wide angle X-ray diffraction (WAXD), and tensile testing. The 18.0 wt % cellulose fibers, with an average diameter of ∼20 μm, possessed a high Young’s modulus up to ∼22 GPa, moderately high tensile strength of ∼305 MPa, as well as high alignment of cellulose chains along the fiber axis confirmed by X-ray diffraction. This process presents a new route to convert microcrystalline cellulose, which is usually used for low mechanical performance applications (matrix for pharmaceutical tablets and food ingredients, etc.) into stiff fibers which can potentially be used for high-performance composite materials.
Open Access
Influence of high-concentration LLDPE on the manufacturing process and morphology of pitch/LLDPE fibres
(MDPI, 2021-09-09) Aldosari, Salem Mohammed; Khan, Muhammad A.; Rahatekar, Sameer S.
A high modulus of elasticity is a distinctive feature of carbon fibres produced from mesophase pitch. In this work, we expand our previous study of pitch/linear low-density polyethylene blend fibres, increasing the concentration of the linear low-density polyethylene in the blend into the range of from 30 to 90 wt%. A scanning electron microscope study showed two distinct phases in the fibres: one linear low-density polyethylene, and the other pitch fibre. Unique morphologies of the blend were observed. They ranged from continuous microfibres of pitch embedded in linear low-density polyethylene (occurring at high concentrations of pitch) to a discontinuous region showing the presence of spherical pitch nodules (at high concentrations of linear low-density polyethylene). The corresponding mechanical properties—such as tensile strength, tensile modulus, and strain at failure—of different concentrations of linear low-density polyethylene in the pitch fibre were measured and are reported here. Thermogravimetric analysis was used to investigate how the increased linear low-density polyethylene content affected the thermal stability of linear low-density polyethylene/pitch fibres. It is shown that selecting appropriate linear low-density polyethylene concentrations is required, depending on the requirement of thermal stability and mechanical properties of the fibres. Our study offers new and useful guidance to the scientific community to help select the appropriate combinations of linear low-density polyethylene/pitch blend concentrations based on the required mechanical property and thermal stability of the fibres.
Open Access
Manufacturing and characterization of regenerated cellulose/curcumin based sustainable composites fibers spun from environmentally benign solvents
(Elsevier, 2017-12-11) Coscia, Marta Gina; Bhardwaj, Jyoti; Singh, Nandita; Santonicola, M. Gabriella; Richardson, Robert M.; Kumar Thakur, Vijay; Rahatekar, Sameer S.
We report a novel manufacturing method for bio renewable regenerated cellulose fibres modified with curcumin, a molecule is known for its medicinal properties. Ionic liquid namely 1-Ethyl 3-Methyl Imidazolium diethyl phosphate (emim DEP) was found to be capable of dissolving cellulose as well as curcumin. Regenerated cellulose/curcumin composites fibres with curcumin concentration ranging from 1 to 10 wt% were manufactured using dry jet wet fibres spinning process using three different winding speeds. All the cellulose and curcumin composite fibres showed distinct yellow colour imparted by curcumin. The resultant fibres were characterised using scanning electron microscopy (SEM), infrared spectroscopy, mechanical testing, and X-Ray diffraction studies. Scanning electron microscopy of cellulose/curcumin fibres cross-section did not show curcumin aggregates in cellulose fibres indicating uniform dispersion of curcumin in cellulose matrix. The cellulose chain alignment in cellulose/curcumin composite fibres resulted in tensile strength ranging from 223 to 336 MPa and Young’s modulus ranging from 13 to 14.9 GPa. The mechanical properties of cellulose/curcumin composite fibres thus obtained are better than some of the commercially available regenerated cellulose viscose fibres. The wide-angle X-ray diffraction analysis of cellulose/curcumin composite fibres showed good alignment of cellulose chains along the fibre axis. Thus, our findings are a major step in manufacturing strong cellulose fibres with a pharmacologically potent drug curcumin which in future could be used for medicinal, cosmetic and food packaging applications.
Open Access
Manufacturing carbon fibres from pitch and polyethylene blend precursors: a review
(Elsevier, 2020-06-05) Aldosari, Salem Mohammed; Khan, Muhammad; Rahatekar, Sameer S.
Carbon fibres are one of the newer, emerging materials with multiple engineering applications, from automobiles to space vehicles. Carbon fibres have high mechanical strength, are lighter than metals with better chemical resistance. There have been reports on the use of polyethylene and pitch precursors for the production of carbon fibres, but there are few reports of how these blends could be used for carbon fibre preparation. Bearing in mind the myriad of benefits that using carbon fibres could bring, this paper reviews recent advances published in the literature on how mesophase pitch and polyethylene could be suitable precursors for carbon fibres. It also provides an introduction to the development of precursor blends that allow the properties of carbon fibres to be tailored to specific applications, including processing techniques, fibre parameters, fibre properties and fibre structure
Open Access
Manufacturing pitch and polyethylene blends-based fibres as potential carbon fibre precursors
(MDPI, 2021-04-29) Aldosari, Salem Mohammed; Khan, Muhammad A.; Rahatekar, Sameer S.
The advantage of mesophase pitch-based carbon fibres is their high modulus, but pitch-based carbon fibres and precursors are very brittle. This paper reports the development of a unique manufacturing method using a blend of pitch and linear low-density polyethylene (LLDPE) from which it is possible to obtain precursors that are less brittle than neat pitch fibres. This study reports on the structure and properties of pitch and LLDPE blend precursors with LLDPE content ranging from 5 wt% to 20 wt%. Fibre microstructure was determined using scanning electron microscopy (SEM), which showed a two-phase region having distinct pitch fibre and LLDPE regions. Tensile testing of neat pitch fibres showed low strain to failure (brittle), but as the percentage of LLDPE was increased, the strain to failure and tensile strength both increased by a factor of more than 7. DSC characterisation of the melting/crystallization behaviour of LLDPE showed melting occurred around 120 °C to 124 °C, with crystallization between 99 °C and 103 °C. TGA measurements showed that for 5 wt%, 10 wt% LLDPE thermal stability was excellent to 800 °C. Blend pitch/LLDPE carbon fibres showed reduced brittleness combined with excellent thermal stability, and thus are a candidate as a potential precursor for pitch-based carbon fibre manufacturing.
Open Access
Natural antimicrobial nano composite fibres manufactured from a combination of alginate and oregano essential oil
(MDPI, 2021-08-13) Lu, Hao; Butler, Jonathan A.; Britten, Nicole S.; Venkatraman, Prabhuraj D.; Rahatekar, Sameer S.
Alginate is a linear biodegradable polysaccharide polymer, which is bio-renewable and widely used for various biomedical applications. For the next generation of medical textiles, alginate nanofibres are desirable for their use in wound dressings that are biocompatible, sustainable, and abundantly available. This study has developed a unique manufacturing process for producing alginate nanofibres with exceptional antimicrobial properties of oregano essential oil (OEO) as a natural antimicrobial agent. OEO with varying degrees of concentration was incorporated in an aqueous alginate solution. Appropriate materials and electrospinning process parameter selection allowed us to manufacture alginate fibres with a range of diameters between 38 and 105 nm. A unique crosslinking process for alginate nanofibres using extended water soaking was developed. Mechanical characterisation using micro-mechanical testing of nonwoven electrospun alginate/oregano composite nanofibres revealed that it was durable. An extensive antimicrobial study was carried out on alginate/oregano composite nanofibres using a range of Gram-positive (methicillin-resistant Staphylococcus aureus (MRSA) and Listeria monocytogenes) and Gram-negative bacteria (Klebsiella pneumoniae and Salmonella enterica), which are common wound and food pathogens. The results indicated that increasing the concentration of OEO from 2 to 3 wt % showed improved antimicrobial activity against all pathogens, and activity was significantly improved against MRSA compared to a non-alginate-based control disk containing OEO. Therefore, our research suggests that all-natural alginate/oregano nanofibre composite textiles offer a new generation of medical textiles for advanced wound dressing technology as well as for food packaging applications.
Open Access
Optical characterisation of polymeric nanocomposites using tomographic, spectroscopic and Fraunhofer wavefront assessment
(SPIE - International Society for Optics and Photonics, 2013-01-25) Koukoulas, Triantafillos; Broughton, William R.; Williams, John; Rahatekar, Sameer S.
Polymers are often embedded with specific nanofillers such that the functional characteristics and properties of the resulting polymeric nanocomposite (PNC) are enhanced. The degree to which these enhancements can be achieved depends not only on the level of particle loading of nanofillers, but most importantly on the resulting dispersion profile achieved within the matrix. Agglomeration (often referred to as clustering) is a result of the mixing process and very much depends on the chemistry between the polymer and nanofiller. Depending on the PNC type, different mixing processes can be applied but the general consensus is that such processes are not repeatable themselves. Not only it is quite difficult to achieve the desired level of dispersion, but in addition there is a limited number of characterization tools that can be employed to routinely check the homogeneity achieved within a produced sample. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) techniques are usually employed, but they are very time consuming, expensive, require special sample preparation and treatment, often produce results that are difficult to interpret and can only analyse very small areas of sample. This work reports on the adaptation and development and three optical techniques that are non-destructive, can accurately characterize the dispersion achieved as a result of the mixing process and can analyse larger material areas. The techniques reported are based on static and dynamic visible and infra-red light scattering.
Open Access
Optimizing the mechanical properties of cement composite boards reinforced with cellulose pulp and bamboo fibers for building applications in low-cost housing estates
(MDPI, 2024-01-29) Taiwo, Anuoluwapo Samuel; Ayre, David S.; Khorami, Morteza; Rahatekar, Sameer S.
Africa is the third-richest continent in the world in terms of bamboo species. Despite these laudable natural resources, most African countries still use asbestos cement board as one of their major building materials. This is chiefly due to the high cost of equipment and technologies associated with non-asbestos-fiber cement board production. The current research seeks to underscore the possibility of utilizing these massive continent resources for non-asbestos-fiber cement board production by employing the existing production process in the asbestos cement industries via an innovatively developed laboratory-simulated Hatschek process. Non-asbestos-fiber cement boards incorporating kraft and bamboo fibers were successfully produced in the laboratory using this innovative method based on Hatschek technology, with natural fibre addition in the range of 2–6 wt.%. Experimental results revealed that the Flexural strength and deflection of the board improved significantly, producing optimum values of 10.41 MPa and 2.0 mm, respectively for composite board reinforced with 10 wt.% and 6 wt.% of kraft pulp and bamboo fibers, respectively. The SEM morphology of the fractured surfaces revealed the mode of composite fracture as well as good interaction at the fiber–matrix interface. Overall, the mechanical properties of the developed composite boards satisfy the minimum requirements of relevant standards based on fiber cement flat sheets and can be employed for internal building applications in low-cost housing estates in developing countries. The outcome of this research indicates that the current industrial production process based on Hatschek technology can be employed for non-asbestos-fiber cement board production using the studied natural fiber.
Open Access
Solar drying of herbal wealth in Eastern Himalaya: a review
(Global Digital Central, 2022-07-31) Chauhan, Priyanka; Pathania, Himani; Shriya, S.; Neetika, N.; Nidhi, N.; Sakshi, S.; Choudhary, Sheetal; Kumar, Rajesh; Sharma, Mamta; Rahatekar, Sameer S.; Kumar, Anil
Solar dryers have proven to be one of the best environmentally friendly approaches for drying purpose of medicinal plants and agricultural crops. Use of solar radiations in drying purpose of plant parts has proven economically as well as environmentally responsible and sensible application. Plants are the treasure of nature with hidden medicinal properties to treat diseases. Plant material should be processed properly for extraction of medicinal molecules in terms drying to decrease the manufacturing loss and to increase the standard of product. Cognizances of ethnobotanical knowledge on plant wealth are extremely beneficial in utilization and exploration of natural resources. Conventionally, low drying temperatures between 30-40°C, with economically beneficial techniques are required to protect sensitive active ingredients. Therefore, the objective of reviewing research in medicinal plant drying is to find out optimum drying temperature and best solar dryer for drying purposes of plant parts in terms of quality and drying costs. Rendering to human requisites, solar appliances for drying purposes will be used as the best alternative to standard sun-drying technique. This review focused on effective drying is demand of present scenario for the application of heat trapped from solar radiations for drying purpose in order to maintain the quality and active ingredients of plants. Conventionally, low drying temperatures between 30-40°C, with economically beneficial techniques are required to protect sensitive active ingredients. Indirect type of solar dryers can easily fulfill all the terms for dying plant products in terms of standard and yield.
Open Access
Structural packaging foams prepared by uni-directional freezing of paper sludge cellulose nanofibres and poly (vinyl alcohol)
(Elsevier, 2019-06-15) Adu, Cynthia; Rahatekar, Sameer S.; Filby, Jyoti; Ayre, David; Jolly, Mark R.
Porous foams from cellulose nanofibres (CNF) and poly-vinyl alcohol CNF/PVA were prepared by uni-directional freezing to create a homogeneous pore structure. The CNF was derived from paper mills sludge (PMS), a by-product of paper manufacturing waste-water treatment. Sodium tetraborate decahydrate (borax) was used as a crosslinking agent. The density of the CNF/PVA foams were 0.03 g cm−3 with a compressive strength of 116 kPa at 20% strain. The foams were competitive to commercial expanded polystyrene (EPS) foam.
Open Access
Superbase ionic liquids for effective cellulose processing from dissolution to carbonisation
(Royal Society of Chemistry, 2017-11-23) Kuzmina, Olga; Bhardwaj, Jyoti; Rizal Vincent, Sheril; Wanasekara, Nandula Dasitha; Kalossaka, Livia Mariadaria; Griffith, Jeraime; Potthast, Antje; Rahatekar, Sameer S.; Eichhorn, Stephen James; Welton, Tom
A range of superbase derived ionic liquids (SILs) was synthesised and characterised. Their ability to dissolve cellulose and the characteristics of the produced fibres were correlated to their specific structural and solvent properties. 17 ionic liquids (ILs) (including 9 novel) were analysed and six ILs were selected to produce fibres: 1-ethyl-3-methylimidazolium acetate [C2C1im][OAc], 1-ethyl-3-methylimidazolium diethyl phosphate [C2C1im][DEP] and the SILs 1-ethyl-1,8-diazabicyclo[5.4.0]undec-7-enium diethylphosphate [DBUEt][DEP], 1,8-diazabicyclo[5.4.0]undec-7-enium acetate [DBUH][OAc], 1,5-diazabicyclo[4.3.0]non-5-enium acetate [DBNH][OAc] and 1-ethyl-1,5-diazabicyclo[4.3.0]non-5-enium diethylphsophate [DBNEt][DEP]. The mechanical properties of these fibres were investigated. The obtained fibres were then carbonised to explore possible application as carbon fibre precursors. The fibres obtained using a mixture of 1,5-diazabicyclo[4.3.0]non-5-enium based SILs with acetate and hexanoate anions (9 : 1), [DBNH][OAc][Hex], showed a promising combination of strength, stiffness and strain at failure values for applications in textiles and fibre reinforcement in renewable composites. Using Raman spectroscopy it is demonstrated that these fibres exhibit a relatively high degree of structural order, with fewer defects than the other materials. On the other hand, analogous fibres based on imidazolium cation with acetate and hexanoate anions (9 : 1), [C2C1im][OAc][Hex] showed a decline in the quality of the produced fibres compared to the fibres produced from [C2C1im][OAc], [C2C1im][DEP] or [DBNH][OAc][Hex].